VTech CS6114-21 User Manual

w w w.vtech.com / hk /telModels: CS6114/ CS6114-2User’s manual

62.5 Install and Charge the Handset BatterySlide open the battery compartment cover.Place the supplied rechargeable battery in the battery compa

7SET UP THE TELEPHONE2.6 Wall MountingYour CS6114,CS6114-2 is designed to mount on a standard wall mounting plate. Refer to the steps below to w

83. GET TO KNOW YOUR PHONE3.1 Overview of the HandsetEARPIECECHARGE LED On when the handset is charging in the telephone base or charger. DO

9GET TO KNOW YOUR PHONE MENU / SELECT In idle mode: Press to access the main menu. In menu / editing mode: Press to conrm and save the settings. Duri

103.2 Overview of the Base StationIN USE LIGHT Steadily on: When the handset is in use. Flashes: When there is an incoming call. Or when the bas

11GET TO KNOW YOUR PHONE2/3 battery power level.1/3 battery power level.Flashes when low battery power level is detected, needs charging.Animation in

123.4 Menu StructureWhen the handset is switched on and in idle mode:Press to enter the main menu.Press pq to move through the available optio

13GET TO KNOW YOUR PHONE3.5 Text and Digit Entry TableThe following table shows you where each letter and punctuation character can be found. Re

144. USE YOUR PHONE4.1 Switch ON/OFF the HandsetWhen the handset is in idle mode, press and hold to switch the handset off. To switch the

15USE YOUR PHONE4.2.5 Call from the Call ListIn idle mode, press to access the call list.ORPress to access CALL LIST. Press again.NOTEThe r

TABLE OF CONTENTS1. IMPORTANT SAFETY INSTRUCTIONS ... 12. SET UP THE TELEPHONE ...

164.4 Adjust Earpiece and Handsfree VolumeThere are 5 levels ( VOLUME 1 to VOLUME 5) to choose from for each of earpiece and handsfree volume.Du

17USE YOUR PHONE4.9 Set the Silent ModeIn idle mode, press and hold to turn off the handset ringer.“RINGER OFF” will be displayed on the scree

184.11.3 Delete a Redial NumberFollow Steps 1 and 2 in the section of Redial a Number from the Redial List.Press then pq to select DELETE.Press .

19USE YOUR PHONENOTESIf OFF is selected, Power Fail Back-Up mode will not be enabled.If AUTO is selected, the registered handset(s) will display “PUT

204.13.3 Answer a Call Using Power Fail Back-Up ModeIf there is only one handset registered to the baseWhen the phone rings, keep the handset on the

21USE YOUR PHONE4.14.2 Transfer an External Call to Another HandsetDuring an external call:Press then pq to select INTERCOM.Press to conrm. If

225. PRIVATE PHONEBOOKYour phone can store up to 70 private phonebook entries with names and numbers. Each phonebook entry can have a maximum of 2

23PRIVATE PHONEBOOK5.2 Review an EntryIn idle mode, press . The rst entry in the phonebook will be displayed.Press pq to browse the phonebook

245.7 Check Phonebook StatusYou can check how many entries have been occupied in your phone and how many phonebook entries are available for you

25PHONE SETTINGS6.1 Date and Time SettingsYou will need to set the correct date and time so that you can get to know when you received call list

4.13.2 Make a Call Using Power Fail Back-Up Mode ...194.13.3 Answer a Call Using Power Fail Back-Up Mode ...

266.2 Handset Settings6.2.1 AlarmYou can use this phone to set an alarm clock. When the alarm time is reached, “ALARM ON” will ash on the d

27PHONE SETTINGS6.2.2 Set the Ringer Melody for External CallsYou can set the melody to personalize your external ringer. A total of 10 melodies a

286.2.5 Set Alert TonesA single beep is emitted when you press a key. You can turn on or off the key tone. You can also turn on the alert tones wh

29PHONE SETTINGSPress then pq to select BS SETTINGS.Press then pq to select CHANGE PIN.Press .Enter the old system PIN.Press then enter the new

306.5.2 Register an Additional Handset through the MenuPress and hold on the base station for about ve seconds, the base station has entered in

31CALLER DISPLAY (NETWORK DEPENDENT)7. CALLER DISPLAY (NETWORK DEPENDENT)7.1 Call ListThis feature is available if you have subscri

327.3 Store a Call List Number into the PhonebookWhile in the call list, press pq to select the desired entry.Press then pq to select ADD TO P

33CALLER DISPLAY (NETWORK DEPENDENT)7.7 Flashing Message Indicator (FMI)The phone is designed to provide visual indication when a new voicemail

348. DEFAULT SETTINGSITEMS Default ValuesDefault Settings of HandsetLANGUAGE ENGLISHEXT RING MELODY 6INT RING MELODY 6INT RING VOLUME VOLUME 5EXT

35TROUBLE SHOOTING9. TROUBLESHOOTINGIf you have difculty with your phone, please try the suggestion listed below.Problem SolutionsMy telephone do

7.6 Set the Category ...327.7 Flashing Message Indicato

36There is interference during a telephone conversation. My calls fade out when I am using the handset.The handset may be out of range. Move it closer

37TROUBLE SHOOTINGCommon cure for electronic equipment.If the telephone is not responding normally, put the handset in the telephone base. If it does

3810. TECHNICAL SPECIFICATIONSBASIC INFORMATIONDimensions Handset: width / depth / height = 48.9 X 35.6 X 164.9 mmCharger: width / depth / height =

39CARE AND MAINTENANCE INSTRUCTIONSTake care of your telephoneYour cordless telephone contains sophisticated electronic parts, so you must treat it wi

40Customer Service CentreSuite 1601, Lever Tech Centre, 69-71 King Yip Street,Kwun Tong, Kowloon, Hong Kong.Customer Service Hotline: (852) 2666 5558T

1IMPORTANT SAFETY INSTRUCTIONS1. IMPORTANT SAFETY INSTRUCTIONSWhen using your telephone equipment, basic safety precautions should always be follo

2The correct disposal of your old appliance/battery will help prevent potential negative consequences for the environment and human health.For more de

3SET UP THE TELEPHONE2. SET UP THE TELEPHONE2.1 Package ContentsThe package contains the following items:Handset (1 for CS6114, 2 for CS6114

42.3 Connect the Base StationPlug the power cable into the base station, plug the other end of the power adapter into the wall outlet not contro

5SET UP THE TELEPHONE2.4 Connect the ChargerPlug the power cable into the charger base.Plug the other end into the power wall socket and switch